Rocrail z21 railcom code#
Rocrail z21 railcom Pc#
Rocrail z21 railcom plus#
Rocrail z21 railcom series#

Added option to set ‘Report feedback from’ to report Feedback and not Turnout status. Prepared for DR5088RC to read back POM commands DR5000 can save loco settings (speed, direction and functions) when pressing the STOP button, at startup, DR5000 will readback those settings when enabled – Modern, low-loss switching external power supply.

– All protocols are translated to the DR.Cmd internal protocol.Įvery Bus/Connection receives specific and relevant data from the internal protocol.

Rocrail z21 railcom series#

– Feedbacks from combining all buses in one series of 1-2048 – 2048 feedback, which is the total of all possible buses. – Offset +4/-4 for MultiMaus compatibility (9999 for long, Maximum short addresses to be set from 0-127) – 126 simultaneous operation / control of locos – Link: The LAN is connected and connected to a switch / hub / router. Intensity increases with the number of active inputs. – There is at least one input on the s88 bus active – The signals to Track-Out and the booster connection are ON.

– The signals to Track-Out and the booster connection are off. – RX: Data is being received from the X-BUS. – RX: Data is received from the computer.

Rocrail z21 railcom code#

Blink Code defines the bus caused the short circuit – Power: Power supply present Programming track indicator The DR502圎XT modules or via the USB/LAN/Wifi interfaces. – Further control possible through X-BUS and/or L.NET (manual)controls, – 4 channels, per channel directly to be controlled/switched, 1 lok and 4 switches. – IR receiver compatible with Uhlenbrock IRIS and Piko DigiFern (or other RC5/36Khz remotecontrols). – The WiFi / LAN module can serve as an AP (access point) as well as a router between the DR5000 and WiFi home network (LAN). – Wifi/LAN settings can be changed via a web-interface – Protocols: Lenz XpressNet and/or L.NET-TCP/IP – Both networks can be accessed via UDP / IP and TCP / IP – bgn Wireless network via internal antenna. Can be connected to a local network via DHCP. Min 14V.Īutomatically switches from Track-Out to Program mode so the programming rail can also be used. – Interface for DR502圎XT modules (bi-directioneel). – Interface for Lenz-RS-Bus feedback modules. the MultiMaus boosters 10764 lan as a booster together with the DR5000! – Interface for XpressNet devices: MultiMaus, LH100 etc. – Interface for L.NET devices including boosters (rail-sync). – Interface for L.NET devices: (manual-)Controllers, Feedback modules etc. – Interface for L.NET devices (Controllers, Feedback modules etc.)

– Communication with computer/control program

Rocrail z21 railcom plus#

Plus the Z71 WiFi throttle.ĮSU Mobile Control II – Requires LNWI or JMRI Roco – Including all web, smart phone and tablet apps. $535 – Total For Others without Shipping!ĬVP Products – Xpressnet Lenz compatible receivers, throttles, etc… $60 – Average USB Computer Connection Device Why is this such a great deal? Let’s Compare: XpressNet – Easily Connect X-Bus Components From Lenz, CVP Including Wireless Receivers And Throttles (CVP OPS T1300) Keep Your LocoNet Clean With Separate LocoNet Connections For Your Boosters (DB150, DB210, Etc.) and Other Devices (UP5, UR92, DS64, SE8C, BDL168, Etc…) POM Read Back When Used With The Digikeijs DR5088RC RailCom – Use Id tags on your JMRI, Rocrail, Etc…, Panel To See What Loco Is In A Specific Block – Great For Dispatchers And Hidden Staging Yards

Rocrail z21 railcom Pc#

On Board Easy Stop & Go Buttons For Track PowerĮasy To Use GUI For Your PC – Easy Decoder Programming, Setting Board Id’s, Monitoring Occupancy Feedback, Booster Stats ex. Programming Track Output – Easily Adjust Your Programming Track Voltage (No Extra Booster Needed For Sound LAN Port Built In – Easy Computer and Router Networking WiFi Built In – Smartphones, Tablets, WiFi Throttles (Roco Z71 Phone and Tablet Apps & WLANmaus) USB Built In – For JMRI, Rocrail, TC, Etc… North American & EU Power Supply Included Simply unhook your current DC power pack and connect the DCC controller and you are up and running.

It comes with everything you need to get started with DCC. This is a very easy to use basic set but easily expandable.